Loading clinical trials...
Loading clinical trials...
Showing 1-20 of 33 trials
NCT07177521
The placement of short implants in post-extraction sockets is a valuable option when residual bone height is limited, minimizing morbidity and treatment time. The management of the peri-implant gap and soft tissues may influence primary stability, hard/soft tissue remodeling, and implant success.
NCT07369583
20 edentulous patients presented for full-arch rehabilitation and was managed using a motion-integrated, fully digital workflow that combined the M-4 protocol in the maxilla with the All-on-4 concept in the mandible. Dual-scan CBCT and facial scans enabled prosthetically driven planning, while stackable and mucosa-supported surgical guides facilitated precise implant placement. Real-time jaw-motion data were incorporated into the design process to individualize occlusion, and definitive monolithic zirconia prostheses were fabricated and delivered on titanium multi-unit abutments using Rosen screws.
NCT07065487
This clinical trial aims to compare three different impression techniques used to fabricate full-arch implant-supported dental prostheses. Accurate impressions are essential to ensure a passive and precise fit of the final prosthetic framework, which contributes to long-term implant success and patient comfort. In this crossover study, participants with four osseointegrated dental implants in the lower jaw will undergo three types of impressions: Conventional splinted impression using polyvinyl siloxane (PVS) material. Standard digital impression using an intraoral scanner. Geometric pattern-assisted digital impression, which incorporates a visual reference pattern to improve scan alignment and accuracy. Each participant will receive all three impression techniques in a randomized sequence, at different time points. The accuracy of each method will be assessed by evaluating the passivity of the resulting prosthetic frameworks using two methods: (1) digital superimposition analysis to measure three-dimensional (3D) spatial deviation, and (2) the clinical "one-screw test" to detect misfit. The study seeks to determine whether digital scanning, particularly with geometric pattern assistance, can provide accuracy comparable to or better than conventional methods. Findings may guide improvements in digital prosthodontic workflows and support more efficient, predictable treatment outcomes.
NCT07014527
custom made subperiosteal implants will be designed using the patients' CT data and will be inserted with the help of a surgical guide and loaded by a screw retained full arch prosthesis. accuracy will be assessed
NCT06965517
patients will be equally and randomly divided into 2 groups. Each group contains seven patients: Digital Group: implant supported maxillary overdenture will be constructed using electronic facebow to record maxillo-mandibular relation. Static Group: implant supported maxillary overdenture will be constructed using the conventional jaw relation method. Radiographic evaluation for crestal bone height around implants using direct digital periapical paralleling cone technique. All data of radiographic evaluation were collected and tabulated then statistically analyzed using SPSS software.
NCT05768295
This Post-Market Clinical Follow-Up study aims to document the success and survival of the Axiom® BL X3 Implants up to 3 years after loading.
NCT05495867
In this case-control study a bioactive implant surface was compared with traditional surfaced implants. Primary objectives: Test the implant stability in post-extractive sites, comparing traditional surfaced implants (MultiNeO CS, control group) to bioactive surfaced implants (NINA- MultiNeO NH, treatment group). Primary outcome endpoints were Implant stability, assessed through Implant stability quotient (ISQ) values and Marginal bone loss (MBL)
NCT06509269
The aim of this study was to evaluate the effect of intraoral scanning versus desktop scanning on the retention and adaptation of maxillary denture bases in completely edentulous patients.
NCT06146153
the aim of this study is to compare the influence of different palatal vault configurations on the accuracy and scan speed of IO scans in cases of completely edentulous arches. The null hypothesis is that there is no difference in scanning time, and trueness and precision of IO scans between class I, II and III palatal vault configurations.
NCT06343441
To compare the accuracy of digital impression and conventional impression for complete-arch implant-supported fixed prosthesis
NCT06276712
To evaluate the clinical and radiographic outcomes of KS implants used to rehabilitate edentulous mandible with dental-retained overdentures, and to compare it with same treatment on TS implants
NCT06209814
The aim of the present study was to evaluate open faced maxillary complete denture with soft acryl resin wing versus conventional heat cured maxillary complete denture regarding the retention and patient satisfaction.
NCT06201169
CAD/CAM-fabricated PEEK bar exhibited greater dimensional deviation in comparison to its titanium counterpart. Nevertheless, patients with PEEK bars reported higher satisfaction levels and lower marginal bone loss when compared to those with titanium bars.
NCT06155630
CAD/CAM (computer-aided design and computer-aided manufacturing) can be a game-changer for better access to care by edentulous patients. Digital overdentures offer potential for more satisfied patients due to better fit and can be provided faster/with lower costs. Providing digital overdentures has potential to enhance access to oral healthcare by the elderly, given the expected benefits (better quality, simpler, faster and more affordable than those obtained traditionally). However, evidence from randomized trials is crucial to verify the relevance of those benefits, especially from the patient perspective, and to confirm those benefits. This trial also serves as an opportunity to improve CAD software and materials, since it will identify technical challenges specific to the provision of digital overdentures. This randomized cross-over trial aims to reveal whether implant-retained mandibular overdentures (IMO) produced by CAD and 3D printing are more satisfactory to edentulous seniors than those fabricated using traditional methods. The investigators will recruit 26 edentulous participants (any sex/gender) amongst previous patients at McGill University, based on the following eligibility criteria: complete edentulism, elderly (age ≥60 years, according to the WHO), need for new maxillary and mandibular complete dentures, ability to complete questionnaires, and previous treatment with two implants in the anterior mandible. Each participant will receive two pairs of dentures, as per the McGill Consensus on Implant Overdentures (i.e., a mandibular overdenture opposed by a maxillary complete denture: (i) one by digital rendering of the mouth, virtual prosthetic design and 3D printing; (ii) a control pair, by traditional clinical and laboratory methods. Each pair will be worn for 3 months according to a random sequence (total follow-up: 6 months after the delivery of the first pair of dentures). Both overdentures will be retained by 2 Novaloc abutments and medium retention matrices. Outcomes will include patient satisfaction ratings and oral health-related quality of life. The investigators will evaluate other patient-reported outcomes, as well as clinician-assessed quality and cost. Outcome assessment will occur at baseline, then at three months after participants have worn each pair of dentures. Following the cross-over, participants will keep their preferred denture pair and return after 12 months to evaluate maintenance requirements, including stained and broken dentures.
NCT05777980
This study examines the effects of prosthetic treatment options applied to edentulous geriatric individuals who applied to Marmara University Faculty of Dentistry on chewing function, food consumption status, malnutrition status and oral health-related quality of life.
NCT04985747
The palatal rugae, refer to asymmetrical and irregular elevations of the mucosa located in the anterior third of the palate, on each side of the median palatal raphe and behind the incisive papilla. The lack of the rugae area on the polished areas of the dentures has been suggested to impact phonetics in denture patients due to lack of tactile feedback. Therefore, the aim of this randomized crossover clinical trial was to compare patients' reported satisfaction with their complete dentures and oral health related quality of life, when provided with a denture with a rough palatal surface in the rugae area compared with a polished palatal surface or an open palatal surface.
NCT03687047
The aim of this project was to evaluate the impact before and after (3, 6, 9, and 12 months) of oral rehabilitation with conventionalof the insertion of new complete dentures (CD) in the oral health-related quality of life (OHRQoL) in total edentulous patients compared to dentate individuals. This is a clinical trial study approved by the Research Ethics Committee (nº 31105714.7.0000.5626 ) which was conducted on 122 patients who attended the clinics of Federal Fluminense University, with the necessity of CD. The eligibility criteria were: healthy patients without disabilities; aged up to 50 years; complete upper and or lower jaw edentulism for a minimum 5 years; the presence of adequate healthy tissue to support the prosthesis; adequate cognitive ability and understanding to respond to the questions posed. It will be excluded patient with motor disabilities, cognitive impairment and people with special needs. After the installation of the CD a follow-up of one week, three, six, nine, twelve and eighteen months will be performed. The Oral Health Impact Profile (OHIP-Edent) instrument will be applied (in form of an interview) to evaluate the impact of CD on OHRQoL. The scores of the OHIP-Edent index will be calculated using the additive method, summing the numeric response codes for each item. Shapiro-Wilk test revealed nonparametric distribution of data. Chi-square, Mann-Whitney U, and Kruskal-Wallis tests were performed for comparing groups according to sociodemographic data. Kruskal-Wallis test was per- formed for comparing groups and treatments throughout time. A significance level of 5% was adopted, and all analyses were performed on Statistical Analysis System (SAS) version 9.3 software. The responsiveness was assessed by analyzing the change of the scores on the scales and subscales. The changes was calculated by subtracting the post-treatment scores from the before-treatment scores. Positive change scores will indicate an improvement in OHRQoL, while negative scores will indicate deterioration.
NCT05352620
The aim of the present study is to clinically and radiographically evaluate the effect of the use of recently developed Smart Box accompanied with OT Equator attachment in retaining of the inclined implant assisted overdenture for atrophic maxilla and to compare the vertical bone changes around axial implants with OT Equator attachment and inclined implants with smart box attachment radiographically using CBCT
NCT04755166
Background: Placement of oral implants is frequently compromised due to atrophy of the alveolar process. Lateral ridge augmentation with an autogenous bone block is frequently necessary to increase the width of the alveolar process before implant installation. However, harvesting of an autogenous bone block is associated with donor site morbidity. Consequently, bone substitutes alone or in combination with particulate autogenous bone graft are used increasingly to simplify the surgical procedure. Animal and human studies evaluating lateral ridge augmentation with Bio-Oss alone or in combination with particulate autogenous bone graft have demonstrated new bone formation and high implant survival. However, the optimal ratio of Bio-Oss and particulate autogenous bone graft for lateral ridge augmentation and long-term implant survival is unknown. Purpose: Test the H0-hypothesis of no difference in long-term implant survival, newly formed bone, volumetric stability of the graft, gained width of the alveolar process and patient satisfaction after lateral ridge augmentation with Bio-Oss alone or in combination with a diminutive amount of autogenous bone graft. Material and methods: lateral ridge augmentation will be performed in 20 adults with two different ratios of Bio-Oss and autogenous bone graft after a split mouth design. Clinical and radiological measurements will evaluate the long-term implant survival. Cone beam computer tomography (CBCT) will be obtained preoperatively, immediately postoperatively, prior to implant placement, 2 years after implant installation and 5 years after implant installation to estimate the volumetric changes of the augmented area. Moreover, the amount of newly formed bone will be estimated by histologic evaluation after implant placement. Conclusion: Long-term implant survival has never been evaluated after lateral ridge augmentation with Bio-Oss alone or in combination with a diminutive amount of autogenous bone graft.
NCT03126942
The objective of this explanatory mixed methods study is to compare a novel attachment system (Novaloc) to a traditional alternative (Locator) for single implants in the mandible of edentate elders. The investigators will carry out a randomized cross-over clinical trial comparing Novaloc attachments to Locators for single-implant mandibular overdentures in edentate elders. Participants will be followed for three months with each attachment type; patient-based, clinical and economic outcomes will be gathered. A sample of 26 participants is estimated to be required to detect clinically relevant differences in terms of the primary outcome (patient ratings of general satisfaction). Participants will choose which attachment they wish to keep, then be interviewed about their experiences and preferences with a single implant prosthesis and with the 2 attachments. Data from the quantitative and qualitative assessments will be integrated through a mixed-methods explanatory strategy. A last quantitative assessment will take place after 12 months with preferred attachment; this latter assessment will enable the observation of attachments' long-term wear and maintenance events.