Protocol for Assessment and Measurement of Diaphragmatic Ultrasound
Ultrasonographic Evaluation of the Diaphragm Protocol:
This protocol focuses on observing and evaluating diaphragmatic function in patients with acute respiratory failure who require non-invasive mechanical ventilation (NIMV) and/or high-flow nasal cannula (HFNC). The ultrasound measurements performed by researchers will be standardized to ensure consistency and accuracy in assessing diaphragmatic function.
Assessment of Diaphragmatic Thickness Collection of arterial blood gases is performed 1 hour after being on the clinician-selected pressure support (PS) level.
Cut-Off Points for Diaphragmatic Assessment Parameters
For the evaluation of diaphragmatic function in patients with acute respiratory failure requiring non-invasive mechanical ventilation (NIMV), the following cut-off points will be used:
Diaphragmatic Excursion:
Diaphragmatic excursion will be measured in centimeters using ultrasound in B-mode and M-mode.
Cut-Off Point: A diaphragmatic excursion of less than 1 cm will be considered indicative of severe diaphragmatic dysfunction, while an excursion greater than 2 cm will be interpreted as excessive diaphragmatic function.
Time to Maximum Inspiratory Amplitude:
This parameter will be measured in seconds from the start of inspiration until the diaphragm reaches its maximum amplitude.
Cut-Off Point: A time to maximum amplitude greater than 0.5 seconds will suggest compromised diaphragmatic function, while a time of less than 0.5 seconds will be deemed normal.
Diaphragmatic Thickening Fraction:
To evaluate diaphragmatic thickness, the following methodology will be implemented:
Patient Positioning:
Explain the procedure to the patient and/or family member. The patient should be positioned supine with the head of the bed elevated between 30 and 40 degrees.
Equipment Setup:
Select a high-frequency linear transducer (7-10 Megahertz) in B-mode. Position the probe in the right intercostal space, drawing an imaginary line between the anterior axillary line and the mid-axillary line, between the eighth and tenth right ribs.
The transducer must be positioned consistently in the same location for each measurement.
Identification of the Apposition Zone:
Locate the apposition zone of the diaphragm, which will appear as a three-layered structure: a central non-echoic layer (the diaphragm) surrounded by two parallel echogenic layers (the peritoneum and the diaphragmatic pleura).
Measurement of Thickness:
In M-mode, the thickness of the diaphragm will be evaluated, which varies according to the phase of the respiratory cycle, being greater during inspiration and less during expiration.
The sweep speed will be increased to obtain at least three consecutive thickening measurements on the screen. The image will be frozen, and three measurements will be taken during three different breaths to obtain an average.
During inspiration, it will be ensured that the thickness is greater, and the distance between the hyperechoic lines will be measured.
During expiration, the distance between the hyperechoic lines will be measured, ensuring that the thickness is less.
Measurement of Diaphragmatic Excursion:
To evaluate diaphragmatic excursion, the following methodology will be implemented:
Patient Positioning:
Explain the procedure to the patient and/or family member. The patient should be positioned supine with the head of the bed elevated between 30 and 40 degrees.
Equipment Setup:
A sector transducer (5-8 Megahertz) or a convex transducer (2-5 Megahertz) will be used in B-mode.
The probe will be positioned in the mid-clavicular line window, immediately below the costal margin, between the mid-clavicular line and the anterior axillary line. The ultrasound beam will be directed cephalically, perpendicular to the posterior third of the diaphragm.
The transducer must be positioned consistently in the same location for each measurement.
Ultrasound of the Diaphragmatic Dome Area:
Using a sector transducer in a cephalic position, the diaphragm will be insonated, adjusting the image so that M-mode is at a 90-degree angle to the dome of the diaphragm.
The sweep speed will be increased to obtain at least three consecutive excursions displayed on the screen. The image will be frozen, and three measurements will be taken during three different breaths to obtain an average.
Measurements of Diaphragmatic Function by Ultrasound
Calculation of Diaphragmatic Thickening Fraction:
This will be calculated by taking the thickening diameter during inspiration, subtracting the thickening diameter during expiration, dividing the result by the thickening diameter during expiration, and multiplying the result by 100%. The diaphragmatic thickening fraction, which varies depending on ventilation support, has reference values indicating diaphragmatic insufficiency (less than 20%) and values above 30%.
Calculation of Diaphragmatic Excursion:
Diaphragmatic excursion (DE, centimeters), inspiratory time (TPIA-dia, seconds), diaphragm contraction speed (DE/TPIA-dia, centimeters per second), and total time (Ttot, seconds) will be calculated in M-mode; diaphragmatic dysfunction will be defined as DE \< 1 cm or paradoxical movement.
Record the data in the corresponding format. Conduct the measurements at the selected flow levels of the high-flow nasal cannula.
The thickening fraction will be calculated using the formula:
((\\text{Thickness during Inspiration} - \\text{Thickness during Expiration}) / \\text{Thickness during Expiration} \\times 100%) Cut-Off Point: A thickening fraction of less than 20% will be considered indicative of diaphragmatic weakness, while a fraction greater than 30% will be deemed excessive.
These cut-off points will allow for a precise and objective assessment of diaphragmatic function, facilitating optimal titration of support pressure during non-invasive mechanical ventilation (NIMV) and thereby improving clinical outcomes in patients with acute respiratory failure.
Study Protocol:
The protocol begins with the admission of the patient with hypoxemic/hypercapnic respiratory failure. Support pressure levels (NIMV cohort) / flow (high-flow nasal cannula (HFNC) cohort) will be applied at the discretion of each center. Patients will be placed in a semi-sitting position at an angle of 30-40 degrees throughout the study. The first diaphragmatic measurement will be taken before the initiation of non-invasive mechanical ventilation (T0) without delaying the start of treatment. The second measurement will be taken 30 minutes after the start of NIMV/HFNC (T1), and the third will be taken 60 minutes after the start of NIMV/HFNC (T2). Measurements will include excursion (centimeters), time to maximum inspiratory amplitude (seconds), total respiratory cycle time (seconds), and diaphragmatic thickening fraction (ED, centimeters) (FTD%), as well as oxygen saturation (SpO2), exhaled tidal volume, respiratory rate, heart rate, and systolic, diastolic, and mean blood pressure at each time point (T0, T1, and T2).
The next measurement of hemodynamic variables (systolic, diastolic, mean blood pressure, heart rate) and respiratory variables (respiratory rate, SpO2) will be conducted one hour after identifying the optimal level of support pressure/flow (defined individually by each center) at which the patient will remain.
Summary of Ultrasonographic Diaphragm Assessment:
Non-Invasive Mechanical Ventilation (NIMV) Patient Cohort Time 0: Prior to the initiation of NIMV support. Time 1: 30 minutes after the initiation of NIMV. Time 2: 60 minutes after the initiation of NIMV.
High-Flow Nasal Cannula (HFNC) Patient Cohort Time 0: Prior to the initiation of HFNC support. Time 1: 30 minutes after the initiation of HFNC. Time 2: 60 minutes after the initiation of HFNC.
