Validation of New Devices Against Ambient Electromagnetic Radiation

Normal healthy men enrolled in the study will be asked to provide semen specimens prior to the use of device. Samples will be produced with a minimum of 48-72 hours of abstinence. Further, the subjects will be blindly assigned with either sham Qi-Shield or Qi-Shield device and will be instructed to use the device for a duration of 8 weeks .Semen samples will be provided by the subjects at 0, 4 and 8 weeks interval. Group 1 study subjects will be provided with sham Qi-Shield device, whereas Group 2 study subjects with be provided with actual Qi-Shield device. Each user will be provided with a small carrier bag to accommodate the device during their travel. The participants are advised to keep the device within 3 meters of range as per the manufacturer instructions for a duration of 8 weeks. Semen analysis All specimens will be collected by masturbation at the Andrology Laboratory after 48-72 hours of sexual abstinence. Samples will be allowed to liquefy completely for 15-20 minutes at 37C before further processing. After complete liquefaction, semen analysis will be carried out using automated LensHooke™X1 PRO semen quality analyzer (Bonraybio Co., Ltd) to determine sperm concentration and motility, progressive motility (Agarwal et al., 2019). Viability will be determined by Eosin-Nigrosin stain if motility is \<25%. Smears of the raw semen will be stained with a Diff-Quik kit (Baxter Healthcare Corporation, Inc., McGaw Park, IL) for assessment of sperm morphology according to strict criteria as described in the WHO, 5th edition guideline. White blood cell measurement When the round cell concentration in the ejaculate is \>1 X million/mL or \>5 round cells per high power field, the sample will be tested for leukocytospermia, i.e. \>1 X million white blood cells/mL. This will be confirmed by the peroxidase or the Endtz test. Measurement of Oxidation Reduction Potential ORP measures the transfer of electrons from a reductant (or antioxidant) to an oxidant. ORP is measured in millivolts (mV). In the current study, ORP will be measured using novel galvanostat-based technology-the MiOXSYS System (Aytu Bioscience, Englewood, CO). Briefly, 30µL of liquefied semen will be loaded on the MiOXSYS sensor. The sensor will be inserted into the MiOXSYS analyzer. Static ORP (sORP), measured in mV, is the integrated measure of the existing balance between total oxidants and reductants in a biological system. Data will be normalized with sperm concentration. ORP will be expressed as mV/ million sperm/mL. DNA fragmentation DNA fragmentation will be assessed via Terminal deoxynucleotidyl transferase-mediated dUTP nick-end labelling assay (TUNEL assay). Briefly, 2 million spermatozoa will be washed in phosphate buffered saline (PBS) and resuspended in 3.7% paraformaldehyde. A total of 2 aliquots (A and B) will be used for each donor, one for ORP measurement and other for measurement of sperm DNA fragmentation. These will be placed on ice for 30-60 minutes at 4C. Thereafter, the spermatozoa will again be washed to remove the paraformaldehyde and then re-suspended in 70% ice-cold ethanol, stored at -20C until the time of analysis. Sperm DNA fragmentation will be evaluated using a TUNEL assay with an Apo-DirectTM kit (Pharmingen, San Diego, CA). Positive and negative kit controls provided by the manufacturer and positive test prepared by treating with hydrogen peroxide controls will be included for each run. Following a second wash in PBS to remove ethanol, the sperm pellets are re-suspended in 50 µL of freshly prepared staining solution for 60 minutes at 37C. The staining solution contains terminal deoxytransferase (TdT) enzyme, TdT reaction buffer, fluorescein isothiocynate tagged deoxyuridine triphosphate nucleotides (FITC-dUTP) and distilled water. All specimens are further washed in rinse buffer and re-suspended in 0.5 mL of propidium Iodide/RNase solution, and incubated for 30 minutes followed by flow cytometric analysis. BD C6 Acuri cytometry analysis: All fluorescence signals of labelled spermatozoa will be analyzed by the flow cytometer BD Accuri Flow cytometer (Becton Dickinson, San Jose, CA). About 10,000 spermatozoa will be examined for each assay at a slow flow rate of \<100 cells/sec. The laser excitation is provided at 2 wavelengths of 488 nm supplied by a solid blue state laser at 20mW and 640 nm powered by 14.7mW diode red laser. Green fluorescence (480-530 nm) is measured in the FL-1 channel and red fluorescence (640 nm) in the FL-2 channel. The percentage of positive cells (TUNEL-positive) will be calculated using the flow cytometer software. Proteomic analysis Individual samples collected from each group will be subjected to 65% percoll gradient to specifically remove the white blood cells. Semen samples will be washed with PBS three times. Once the supernatant is removed, spermatozoa will be solubilized in radio-immunoprecipitation assay (RIPA) lysis buffer containing the proteinase inhibitor cocktail. After complete lysis of the spermatozoa, protein concentration will be determined using a bicinchoninic acid (BCA) kit and equal amounts of proteins will be fractionated using SDS-Page 1D gel electrophoresis. Separated bands will be cut from a single Coomassie blue stained 1D gel and analyzed. The bands will be washed, reduced, alkylated, and digested with trypsin. The digests will be separated by capillary column LC-tandem MS and the CID spectra searched against the human reference sequence database. Functional annotation and enrichment analysis will be performed using publicly available bioinformatics annotation tools and databases such as GO Term Finder, GO Term Mapper, UniProt, Software Tools for Researching Annotations of Proteins (STRAP), Database for Annotation, Visualization and Integrated Discovery (DAVID) (http://david.niaid.nih.gov), and proprietary software package such as IPA (Ingenuity Pathway Analysis) from Ingenuity® Systems, used to obtain consensus-based, comprehensive functional context for the large list of proteins derived from proteomic study. The data will be subjected to STRING (Search Tool for the Retrieval of Interacting Genes/Proteins), a biological database and web resource of known and predicted protein-protein interactions. This will help in identifying critical proteins involved in reproductive function. Data analysis All the data will be analyzed using the using the MedCalc Software (V. 17.8; MedCalc Software, Ostend, Belgium). Paired t-test will be used if the distribution is normal. Whereas, Wilcoxon signed rank tests will be used for parameters that do not follow normal distribution. For paired T-test comparisons based on 20 samples for each experiment, the power should be least 90% for parameters where a coefficient of variation is no more than 20%.