Feasibility Study of a Non-invasive Device to Quickly, Easily and Accurately Measure Respiration in a Clinical Setting

The study will be divided into 2 phases - 1st phase will last 1.5 months and will aim to recruit at least 50 patients and at most 100 patients. This phase will aim to recruit near-equal split of patients across the 3 disease states of COPD, asthma and pneumonia - 35 COPD, 35 Asthma and 30 pneumonia patients. The 2nd phase will last 3 months and will aim to recruit at least 50 patients. This phase can have a mix of patients having either COPD, asthma, pneumonia, congestive heart failure or any other respiratory diseases The aim in the 1st phase is to benchmark the device against manual counting of respiration (number of breaths per minute). The aim in the 2nd phase is to benchmark the device against existing technologies, namely lead-based-ECG sensing, acoustic sensing and capnography. This phase can have a mix of patients having either COPD, asthma, pneumonia or any other respiratory diseases Following is the study protocol that will be implemented over the 2 phases: Phase 1: 1.5 months - 100 patients - General Wards (Time taken for each patient is 25 mins) a. Delegated study team members will brief the study details to the potential participants. Investigators will answer the query from potential participants if any, and complete the consent process. (5 mins) b. Trial coordinator will setup the device as follows: (10 mins) i. Disinfect the device by wiping with an alcohol swab, ii. Turn on the sensor - ensure the USB dongle is connected to the RIGHT ports on the laptop - check that the USB dongle AND the sensor light is NOT blinking iii. Paste the sensor on patient using a medical-grade adhesive tape. c. Trial coordinator will begin data collection by double click the software .exe file - select the COM ports and enter participant no. (a folder will be created in root directory for the participant number) d. Click "run" button on the software and start to manually count the number of breaths after 1 minute. After 1 minute, the number of breaths counted manually will be recorded on the case report form.4 rounds of 1-minute measurements will be taken e. Trial coordinator will turn off the device and pass it back to team-member or keep it. Trial coordinator will remove the medical-grade adhesive tape and throw it away. (5 mins) f. Team-member will post-process the collected respiration data, benchmark against the manually counted data in the data collection form provided by trial coordinator and discuss the results with investigating P.Is. Phase 2: 3 months - 50 patients - Medical intensive care units (MICU), medical dependency units (MDU), cardiology high dependency units, and general wards (for congestive heart failure patients) (Time taken for each patient is 30 mins) g. Delegated study team members will brief the study details to the potential participants. Investigators will answer the query from potential participants if any, and complete the consent process. In the event that the patient is unable to provide consent, the next-of-kin will be approached for consent. (5 mins) h. Trial coordinator will setup the device as follows: (10 mins) i. Disinfect the device by wiping with an alcohol swab, ii. Turn on the sensor - ensure the USB dongle is connected to the RIGHT ports on the laptop - check that the USB dongle AND the sensor light is NOT blinking iii. Paste the sensor on patient using a medical-grade adhesive tape. iv. Attach another sensor on the patient's finger using an adapter. The purpose of this is to collect heart rate and Sp02, and to calculate respiration from the collected data. i. Trial coordinator will begin data collection by double click the software .exe file - select the COM ports and enter participant no. (a folder will be created in root directory for the participant number) j. Click "run" button on the software. After 1 minute, the number of breaths, heart rate and Sp02 from other technology devices will be recorded on the case report form.4 rounds of 1-minute measurements will be taken. k. Trial coordinator will turn off the device and pass it back to team-member or keep it. Trial coordinator will remove the medical-grade adhesive tape and throw it away. (5 mins). Trial coordinator will also remove the device and adapter from the finger location. l. Team-member will post-process the collected respiration data, benchmark it and discuss the results with investigating P.Is. All data collected will be anonymous and no video-taping will be done. The trial coordinator will act as the control arm. They will measure the respiration or breathing rate of the subject manually - by counting the number of breaths per minute. The non-control arm will be the device itself and it will be benchmarked to the manual respiration data collected by the trial coordinator. The data collected will be kept with the P.I and confidentially of the data will strictly be maintained. The case report forms or the collection forms will be passed to the P.I. and kept safely. The subject may choose to withdraw from the study at any time. The device is based on multi-modal sensing using illumination at extremely low emission levels on the order of microwatts. This sensing technique is able to detect the micro-vibrations along the neck due to breathing.