Comparison of Glenoid Position Using SmartBones

The proposed clinical study will enroll patients indicated for standard of care anatomic total shoulder arthroplasty. Participants will receive all pre-operative testing, intra-operative care including all implants and post-operative care that is standard of care and specific to the surgeon's and patient's decisions for care. The only change for Groups 2, 3 and 4 will be the type of surgical instruments used to place the glenoid guide pin, retention of the humeral head to obtain bone tissue, placement of the beads and post-operative CT scanning. In all cases the surgeon is able and allowed to use their own surgical judgment to place the guide pin, prepare the bone and place the desired implant. In all cases, the surgeon can use any and all of the standard instruments or guides provided by the implant manufacturer as the surgeon would use if the patient was not enrolled in the study. If the surgeon chooses not to use the IRI or RTI technology, then this would be noted as a deviation in plan, the reasons recorded and the patient would be excluded from the study without post-operative imaging and their pre-operative and intra-operative data would be analyzed for the purpose of understanding the reasons for failure of the IRI or RTI technology to provide assistance for refinement of the technology. The participating surgeons will be Dr. Joseph Iannotti, Dr. Eric Ricchetti and Dr. Peter Evans. Patients may have surgery at either Cleveland Clinic main campus or at Euclid Hospital. If the procedure is performed at Euclid Hospital, post-operative CT scan and RSA (if chosen), will be performed at main campus within 3 weeks after surgery. The patient will be made aware of this at the time of enrollment and consent. Using manufacturer (RSA biomedical, Umsa Sweden) provided beads and injector gun, four to five 1 mm tantalum beads will be placed in the coracoid, acromion and glenoid. Exact placement of these beads is at the discretion of the surgeon. Patient anatomy and operative exposure will guide the surgeon to the best places to inject the beads; however the surgeon will not be confined to a specific amount of beads in a specific location. The beads just need to be spread out amongst the coracoid, acromion, and glenoid to establish reference points for the RSA imaging. Prior studies looking at shoulder joint kinematics and implant position have used this methodology of bead placement with successful study related outcomes. Investigators have successfully placed bone beads in 22 patients currently treated in the ongoing IRI clinical study without any difficulty or adverse events during or after surgery. Postoperatively, all patients will receive a CT with Metal Artifact Reduction (MAR)and RSA (if chosen) within 3 weeks of surgery. This will be a CT Scan performed with the patient's arm by the side in a supine position using metal artifact reduction techniques. In addition patients will receive a second CT scan and RSA imaging, provided they originally got RSA, performed 1 year (± 1 month) from surgery. The second CT scan will be performed with MAR techniques and with the patient in the lateral decubitus position with their arm in the overhead position, again using metal artifact reduction techniques. The second set of images, produced with a different body and arm position, also decreases metal artifact than those obtained with the arm placed by the side. This position cannot be comfortably obtained until 3- 6 months after surgery and require healing of the tissues and rehabilitation of the shoulder. Investigators have shown that in a small number of patients the glenoid component can shift in position within the first 3-6 months after surgery making the first CT Scan more accurate for implant position. The images obtained from the postoperative CT scans are placed back into the surgical software and the 3D reconstruction of the postoperative scapula with the implants is compared to the preoperative plan. Using measurement tools within the software, developed at the Cleveland Clinic, investigators will compare the position of the actual glenoid component placed in the patient with the desired position specified by the plan. The use and validation of these imaging methods to precisely measure implant position has been performed at the Cleveland Clinic in a prior IRB approved clinical trial (IRB 10-582). Preoperatively, the high resolution quantitative CT will measure volumetric bone mineral density and the trabecular network of the glenoid. When available, this will be applied to the preoperative CT for those patients at Cleveland Clinic, Main Campus. Patients who have their preoperative CT completed at non Main Campus facilities will have the standard of care preoperative CT. This will be done at the same visit for the standard of care preoperative CT. Micro CT imaging, which creates a 3D reconstruction of the fine bone structure, in addition to microarchitecture analysis and mechanical testing, will allow assessment of the bone tissue taken from the bone core sample. Between the preoperative imaging and the bone tissue analysis, investigators will have data to properly determine the quality of the bone stock surrounding the implant. Further correlating these data with RSA and 3D CT imaging of implant movement, investigators can fully develop cause and effect of bone quality on glenoid component loosening. Study Statistics and Analysis: Our goal is to have 20 subjects in each of the 4 treatment groups for a total of 80 subjects. To control for subject withdrawal for various reasons after enrollment, we will enroll up to 120 subjects. Statistical analysis plan: Average deviations from plan for the 4 treatment groups will be compared using mixed-effects ANOVA methods. Random effects will be included to account for correlation between observations introduced as a consequence of multiple observations of deviation being taken on a particular surgeon. If significant differences are found, multiple comparisons based on the ANOVA model will be made to compare each pair of groups, and will use Holm's step-down procedure to control the family-wise error rate of the tests. All analyses will be done by Colin O'Rourke of Quantitative Health Sciences at Cleveland Clinic using R software (version 3.0.0, Vienna, Austria). A significance level of 5% will be used for all testing.